Can-Am ATV Forum / Aurorawheelers   Can-Am ATV Forum / Aurorawheelers
Enter AURORAWHEELERS in the coupon area for a discount

Sneak Peak Renegade X with RDC FULL Bracket lift...

This is a discussion on Sneak Peak Renegade X with RDC FULL Bracket lift... within the Can-Am Renegade forums, part of the Can-Am ATV Discussion category; These were taken last night, total height gains at this time were as follows Front + 2-1/4" Foot peg + 1-1/2" Rear + 7/8" I ...


Go Back   Can-Am ATV Forum > Can-Am ATV Discussion > Can-Am Renegade


   
Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 02-05-2010, 09:37 PM
Rubberdown's Avatar
Member
Feedback Score: 0 reviews
 
Member #5161
Join Date: Jul 2008
Location: , ,
Posts: 60
Thanks: 11
Thanked 3 Times in 2 Posts
View Rubberdown's Photo Gallery(0)
Default Sneak Peak Renegade X with RDC FULL Bracket lift...

These were taken last night, total height gains at this time were as follows

Front + 2-1/4"

Foot peg + 1-1/2"

Rear + 7/8"







I wasnt happy with this final gain so I made some changes and re-installed tonight, new total height gains are currently as follows,

Front + 2-1/4"

Foot peg + 1-1/2"

Rear + 1-1/2"

Sorry, to cold out there tonight to take any new pics.

This kit will likely stay the way it is for Hammy for the time being unless he wants to leave the machine here a little bit longer. I will be making another small change to the rear kit to try and get it to 2 full inches of lift but wont be able to do so until Monday or Tuesday.

Just for anyone that is wondering how I take my measurements, I measure iand get a height front side and read before I take it apart, but only after I have road it around and over a few little bumps in my back yard, etc etc to get the suspension settled down to where it would be right after a ride. THEN I do my magic and design and install the lift and after I set it down off the hoist, they usually have LOTS of lift, but again, I take it for a little boogy and settle it all in and then re-measure it.
__________________
2009 Sportsman 850 XP EPS
Rubberdown Customs Mod list
-2nd Generation 2-1/2" lift kit.
-Bar Ends
-Gas cap
-Rad overflow Cap
-Aluminum Swamp Lox (on 29.5's for racin)


30" Zilla's on 14" SS212's
ATV GURU Bumpers
QSC Slip on Exaust (sounds AWESOME)
QSC Clutch kit (not installed yet)

Coming soon, Rubberdown Customs Racing Footwells!!!

04.5 500HO, RDC Lift Kit, Gorillas up front, Turners in the rear, RDC Aluminum Gas Cap and Overflow cap, RDC Bar Ends, RDC Throttle cover, HSP motor job, HSP Full Exhaust, QSC Clutch Kit, 29.5's on RDC Aluminum Swamp Lox, Rad racked, snork'd, goes real fast in the bog pit with around 46 HP!!!

Gone but not forgotten, 04.5 500HO - Modded to the nuts, used for trail and light racing, or deep sea trolling LOL
Reply With Quote
Sponsored Links
Can-AmForum.com is the premier Can-Am ATV, Can-Am Outlander, Can-Am Renegade Forum on the internet. Registered Users do not see these ads. Please Register - It's Free!
       
  #2  
Old 02-05-2010, 09:46 PM
Senior Member
Feedback Score: 0 reviews
 
Member #1863
Join Date: Jan 2007
Location: , ,
Posts: 122
Thanks: 0
Thanked 2 Times in 2 Posts
View cam-law's Photo Gallery(0)
Default

how ya gettin 1.5" more in back without popin the axle out ?
Reply With Quote
  #3  
Old 02-05-2010, 09:51 PM
Hampster rancher's Avatar
Member
Feedback Score: 0 reviews
 
Member #8316
Join Date: Nov 2009
Location: S/W Ontario
Posts: 94
Thanks: 3
Thanked 4 Times in 4 Posts
View Hampster rancher's Photo Gallery(0)
Default

I'm trying out a set of Rhino brand axles ( from SuperATV ). They are built "like" Gorilla's, but they are MUCH cheaper. Just giving them a try to see if they will work in this application.
__________________
TEAM RDC #72
'09 RENEGADE "X", GenII RDC lift, Rhino axles in the back, EDL's on RDC SwampLoX, RDC Blade gas cap, QSC MudPro clutch kit,
Reply With Quote
  #4  
Old 02-05-2010, 09:55 PM
Rubberdown's Avatar
Member
Feedback Score: 0 reviews
 
Member #5161
Join Date: Jul 2008
Location: , ,
Posts: 60
Thanks: 11
Thanked 3 Times in 2 Posts
View Rubberdown's Photo Gallery(0)
Default

what he said ^^^^
__________________
2009 Sportsman 850 XP EPS
Rubberdown Customs Mod list
-2nd Generation 2-1/2" lift kit.
-Bar Ends
-Gas cap
-Rad overflow Cap
-Aluminum Swamp Lox (on 29.5's for racin)


30" Zilla's on 14" SS212's
ATV GURU Bumpers
QSC Slip on Exaust (sounds AWESOME)
QSC Clutch kit (not installed yet)

Coming soon, Rubberdown Customs Racing Footwells!!!

04.5 500HO, RDC Lift Kit, Gorillas up front, Turners in the rear, RDC Aluminum Gas Cap and Overflow cap, RDC Bar Ends, RDC Throttle cover, HSP motor job, HSP Full Exhaust, QSC Clutch Kit, 29.5's on RDC Aluminum Swamp Lox, Rad racked, snork'd, goes real fast in the bog pit with around 46 HP!!!

Gone but not forgotten, 04.5 500HO - Modded to the nuts, used for trail and light racing, or deep sea trolling LOL
Reply With Quote
  #5  
Old 02-07-2010, 01:45 PM
Rubberdown's Avatar
Member
Feedback Score: 0 reviews
 
Member #5161
Join Date: Jul 2008
Location: , ,
Posts: 60
Thanks: 11
Thanked 3 Times in 2 Posts
View Rubberdown's Photo Gallery(0)
Default

More updates, KIT DESIGN FINISHED!!!!

GC in the front under the skid plate is 14"
GC in the rear under the skid plate is 14-1/4"

Total height gain in the front was 2-1/4" and around 1-7/8" in the rear, leveled out the machine really nice actually.















__________________
2009 Sportsman 850 XP EPS
Rubberdown Customs Mod list
-2nd Generation 2-1/2" lift kit.
-Bar Ends
-Gas cap
-Rad overflow Cap
-Aluminum Swamp Lox (on 29.5's for racin)


30" Zilla's on 14" SS212's
ATV GURU Bumpers
QSC Slip on Exaust (sounds AWESOME)
QSC Clutch kit (not installed yet)

Coming soon, Rubberdown Customs Racing Footwells!!!

04.5 500HO, RDC Lift Kit, Gorillas up front, Turners in the rear, RDC Aluminum Gas Cap and Overflow cap, RDC Bar Ends, RDC Throttle cover, HSP motor job, HSP Full Exhaust, QSC Clutch Kit, 29.5's on RDC Aluminum Swamp Lox, Rad racked, snork'd, goes real fast in the bog pit with around 46 HP!!!

Gone but not forgotten, 04.5 500HO - Modded to the nuts, used for trail and light racing, or deep sea trolling LOL
Reply With Quote
The Following 2 Users Say Thank You to Rubberdown For This Useful Post:
Hampster rancher (02-07-2010), mac102004 (02-08-2010)
  #6  
Old 02-07-2010, 02:02 PM
The DUKE's Avatar
Senior Member
Feedback Score: 0 reviews
 
Member #1949
Join Date: Feb 2007
Location: , Ontario, Canada
Posts: 443
Thanks: 0
Thanked 4 Times in 4 Posts
View The DUKE's Photo Gallery(1)
Default

Very nice man, Great work Paul.....
__________________
2010 Outlander 800R Camo
LTE slip on BLACK
Mudbugs on SS312's
2inch RDC lift
Dalton
Snorkel your atv Kit


HEAVY RIGHT THUMB
Reply With Quote
  #7  
Old 02-07-2010, 02:25 PM
Rubberdown's Avatar
Member
Feedback Score: 0 reviews
 
Member #5161
Join Date: Jul 2008
Location: , ,
Posts: 60
Thanks: 11
Thanked 3 Times in 2 Posts
View Rubberdown's Photo Gallery(0)
Default

Thank you.
__________________
2009 Sportsman 850 XP EPS
Rubberdown Customs Mod list
-2nd Generation 2-1/2" lift kit.
-Bar Ends
-Gas cap
-Rad overflow Cap
-Aluminum Swamp Lox (on 29.5's for racin)


30" Zilla's on 14" SS212's
ATV GURU Bumpers
QSC Slip on Exaust (sounds AWESOME)
QSC Clutch kit (not installed yet)

Coming soon, Rubberdown Customs Racing Footwells!!!

04.5 500HO, RDC Lift Kit, Gorillas up front, Turners in the rear, RDC Aluminum Gas Cap and Overflow cap, RDC Bar Ends, RDC Throttle cover, HSP motor job, HSP Full Exhaust, QSC Clutch Kit, 29.5's on RDC Aluminum Swamp Lox, Rad racked, snork'd, goes real fast in the bog pit with around 46 HP!!!

Gone but not forgotten, 04.5 500HO - Modded to the nuts, used for trail and light racing, or deep sea trolling LOL
Reply With Quote
  #8  
Old 02-07-2010, 02:55 PM
Voodoo's Avatar
Super Moderator
Feedback Score: 0 reviews
 
Member #2820
Join Date: May 2007
Location: Winnsboro, LA , USA
Posts: 11,840
Thanks: 0
Thanked 52 Times in 52 Posts
View Voodoo's Photo Gallery(8)
Default

Looks great man.
__________________
Voodoo

09 Outty 800R..12:1 HC Pistons...HMFw/PCIII, 25" Horns

Reply With Quote
  #9  
Old 02-07-2010, 03:02 PM
Hampster rancher's Avatar
Member
Feedback Score: 0 reviews
 
Member #8316
Join Date: Nov 2009
Location: S/W Ontario
Posts: 94
Thanks: 3
Thanked 4 Times in 4 Posts
View Hampster rancher's Photo Gallery(0)
Default

I'm VERY pleased with it!!! It looks WAY bigger in person than in pics!!


__________________
TEAM RDC #72
'09 RENEGADE "X", GenII RDC lift, Rhino axles in the back, EDL's on RDC SwampLoX, RDC Blade gas cap, QSC MudPro clutch kit,
Reply With Quote
  #10  
Old 02-08-2010, 09:38 PM
Member
Feedback Score: 0 reviews
 
Member #7471
Join Date: Aug 2009
Location: illinois
Posts: 39
Thanks: 1
Thanked 0 Times in 0 Posts
View jacewebb's Photo Gallery(0)
Default .

i dont understand. my x is brand new( 35 miles) and i have very overly inflated 27" tires and front shocks cranked up 4 rounds and i still dont thinki even have 10 inches of ground clearance.

Last edited by jacewebb; 02-08-2010 at 09:44 PM. Reason: .
Reply With Quote
Reply

Lower Navigation
Go Back   Can-Am ATV Forum > Can-Am ATV Discussion > Can-Am Renegade

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Rear bracket lift rancher12 Can-Am Outlander 32 01-15-2010 08:46 AM
Rear Bracket Lift??Anyone?? aksledr Can-Am Outlander 9 12-02-2009 06:10 PM
MrRPM Cooler Kit sneak peak john cannon Can-Am / BRP 61 09-29-2009 06:25 AM
Outlander Bracket Lift outlandish Members Rides / How To Videos 1 03-23-2009 09:28 PM
Bracket Lift How-To Video Nutmeg Can-Am / BRP 10 02-13-2008 02:12 PM


All times are GMT -4.5. The time now is 01:49 PM.

Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2010, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.3.2