Can-Am ATV Forum banner
clutch kit

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 27 Results
  1. Can-Am Outlander
    Anyone ever done this? I got a 2020 450 DPS I have been messing around with, I put a WKP Secondary clutch spring on it, and thinking about throwing some 28s on it but the tires I am after are a little on the heavier side... I personally think it will turn them with the WKP secondary spring, but...
  2. Can-Am Renegade
    Hey guys I was just reading this thread, it was pretty interesting and had me thinking. So the guys were saying the renegade XMR 1000 comes with the same clutch as the renegade 1000 just different spring/weights (at least in the earlier years). Then the thread ended My questions would be, if...
  3. Can-Am Maverick
    My maverick is almost what id call jumpy when I go to take off, it jerks and bucks when I take off but is fine once I'm up to 20 mph or so. It also will smoke my belts when I'm in a mud hole or going up a steep grade from take off. I know it has something to do with my clutches, bought a new...
  4. Can-Am Outlander 6x6
    Installed some blackwater evos 28x10x12, loving the new tires :th_smiliewoo:, and was interested in getting a little bit more power down to them, especially in some pretty mucky areas up here in Alaska. Was looking into a clutch kit, but there is not a lot of info on them for the outlander 1000...
  5. Can-Am Outlander
    My wife's 2008 Outlander 400 desperately needs some low end to mid range torque. It is stock other than new Kenda 8 ply Bearclaws. I assume a clutch kit may be one way to go. Any suggestions for a clutch kit or any other suggestions. We do mostly trail riding in the Northeast. Not a ton of...
  6. Can-Am Outlander
    My wife's 2008 Outlander 400 desperately needs some low end to mid range torque. It is stock other than new Kenda 8 ply Bearclaws. I assume a clutch kit may be one way to go. Any suggestions for a clutch kit or any other suggestions. We do mostly trail riding in the Northeast. Not a ton of...
  7. Can-Am Outlander
    I'm turning my 2013 outlander 650 into a 840 with gen 2 cams I need to know if anyone's done this if so what clutch kit did you use to get the clutch set up? Don't have enough money to go with a full primary. All info is helpful thanks
  8. Can-Am Outlander
    I'm planning on adding some 28" mud/snow tires to my 2014 outlander 1000 and after some research I realized that I need a clutch kit. I was told all I need are new primary clutch arms and a primary clutch spring. From what I understand Dalton Industries is a good brand and I'm leaning a little...
  9. Can-Am Outlander
    I'm looking into getting some mud/snow tires for my outlander 1000. I'm still deciding on either 27" black mambas or 27" swamp lites, but both sets of tires are a good deal heavier than the stock tires. So I'm not sure if I need a heavier clutch. Does anybody know if I need a heavier clutch for...
  10. Can-Am XMR
    Im thinking about putting the DBO 1000R clutch kit on my 2014 Outlander XMR 1000 and i was wondering if anybody had any experience with this kit and what the pros and cons were of it and maybe how easy or hard was the installation and why...thanks in advance.
  11. Can-Am Outlander
    I am new to this forum and still learning how to use it properly. I am trying to decide between the qsc clutch kit or a whole new QSC primary for my 2008 Outlander XT. . What results will I notice if I went with the kit and how would that compare to the whole new primary? I keep reading that...
  12. ATV Tech Tips
    I will be buying a clutch kit for my '13 outlander 800xt this thursday. I have a $100 credit that I have to spend for QSC. I refuse to pay $400 for the adjustable clutch kit with QSC so Im stuck with the fixed weight kit for $210ish minus my $100 credit. 1st... has anyone tried it? The fixed not...
  13. Can-Am Outlander
    I want to install a clutch kit in my 2013 outlander 800xt. Anyone know what the stock clutch weights/cam arms weigh? I called VFJ and he said his kit wouldn't work in my quad because the weights are to light from the factory. And does anyone know if the 2013 renegade 800 weights are lighter or...
  14. Can-Am Renegade
    Hi guys, I have a 08 Renegade 800 EFI, I've just ordered 29.5" outlaw tires and I am looking for a 2" lift. Any recommendation for the lifter? pipe, high or signature? Can't understand the difference ! (can a link be shown?) Now I am looking to buy a clutch as well, Dalton but I don't really...
  15. ATV Tech Tips
    2013 outty 800xt. I want more bottom end and mid so I am definately going to be buying a clutch kit. No full clutch for me as i do not need it. I ride 50% hard trail and 50% thick mud. I am not sure whick kit will be best for me as they are similar price. I am running 27" zillas now and going...
  16. Can-Am Outlander
    Ok i recently put on 27" zillas on my 2013 outty 800xt. I know i do not need a clutch with these light tires but i feel its to blah..... im used to how agressive my 850xp felt when you hit the throttle and i kind of want that back minus the polaris. Lol. My machine is only a month old so going...
  17. Dalton Industries
    Ok so I have looked all over and don't understand the clutch kits to much. I have a 2009 renegade 800. I have 27inch sti black diamond xtr's on it 29lbs front 32lbs rear. I'm looking to get the bike to wheelie as easy or easier if possible than when it was stock. I ride mostly trails with a...
  18. Can-Am Outlander
    Im going to invest in a dalton clutch kit for my 1000. When installing the new arms do I add the weights they supply or leave them out when running 28" mud tires?
  19. Can-Am Outlander
    I've got a 2010 Outlander 800. Rad re-locate and some other trinkets on it. Recently put 29.5" outlaw 2's on her, and wondering what people would recommend for a clutch kit here? Also, thoughts on exhaust? Looking at slip-on LTE, or is it worth going with a full exhaust system? And brands...
1-19 of 27 Results
Top