Search Results for ‘clutch’

I have a renegade 850 and i blew the secondary clutch is there any websites that have them cheap enough for my renegade 850

So i have a 2017 can am renegade 850 and i need a new secondary clutch i was wondering if the secondary clutch on a 450 renegade would work on my 850

I have a 2014 outlander 1000xt that began making a grinding noise in low gear while decelerating or letting off the throttle. Does anyone have any ideas as to what may be causing this? Otherwise it seems to operate normal, i included a video of it making the noise going down my driveway in low...

Hello All, I just read another thread related to engine breaking and the one-way bearing so I thought it would be good time to ask a few questions. How often should this service be performed? Type of grease: ISOFLEX NB 52 I belive is the recommended stuff to use - a very light coating. What...

good morning everyone, I have a 2012 outlander 1000 I bought a cv tech primary awhile ago now, I keep going through belts like it’s going out of style! I bought it from peakboys. I feel like I’m missing out on a lot of bottom end. I have 28s Maxxis zillas will not be going any bigger. I like the...

I have a 2019 Outlander 850 XMR that I usually run on stock 26's and typically it gets babied. I am aware of the normal Can-Am noise when you are braking or on and off the throttle. Which is what this bike has always had since it was new. I just rode 100+ miles in the rocky mountains with her...

hello i recently purchased my first outlander, iv only had it for a few days but and i knew it had some issues when i bought it but i couldn't pass up the deal, well i took the first ride on it yesterday and here are some of the issues, 1. diff seal is leaking, 2. it over heats and throws itself...

I’ve recently purchased a 2006 Outlander 800 that has been 1000 swapped. Has a cam, snorkel, radiator relocate, hmf exhaust, and has been tuned. (Guy also claimed it has high performance clutch kit). When i bought it the belt was blown so i ordered a new one, installed it, and the it was acting...

Hi all, I have a 2007 800 Max XT that I keep in very pristine condition. It is almost exclusively driven on sand and has about 2400 miles on it. Original belt change oil and fluids on schedule, etc., etc. Yesterday my wife and I were out on the sand on totally flat ground. We had just come out...

Hello, I bought used 2015 Outlander 500 XT. The throttle response is really slow on the bottom, the top seems fine. I have changed the spark plugs, battery and the belt, but still the same. Any advice on what to check? The engine has 500 hours on it. Is it time to change pistons? Was...

Title says it all, I found a wrecked 07 800 can am guy is willing to sell the clutch to me and I have a 2004 400 can am and I'm wondering if it will just bolt right up.

Was replacing the oneway bearing in my outlander 1000 and when unscrewing the clutch tool i heard a pop , and the clutch tool is snapped inside of the secondary. Looking for the best an easy way to remove the bolt inside the clutch , thanks in advanced great way to end my night lol

In search of primary clutch for 2015 og maverick!

Anyone know where the problem is ? i also tright removing my CVTECH and secondary and put the original CanAm Clutch main / secondary on it still same problem but not so loud, my guess is the transmission or is it normal? it only comes when putting it in gear like H/L in Neutral it is not there...

I have what sounds to be a very serious issue going on with my 2016 outty xmr1000. I will attach a video of said issue. Have had this banging noise when accelerating, and in reverse. I have changed everything from entire suspension to replacing the whole front diff, has been a nightmare cost...

Really looking for some feedback on what type of spring rates would be best for 33s and brand i should go with. I know it needs clutches in general I’m gathering money for them but in the time being i wanna do springs so i can ride while i save up for clutches. 17 maverick 1k dps

Does anyone know if all the parts from the Funduro F650 motorbike which looks like the engine is exactly the same as the DS650x will fit main the clutch plates as if you go onto ebay they want £165 for a clutch for the DS and the funduro if its the same is only £75. I believe the only...

Hi guys, back to my XMR570, I saw on ebay some EPI springs for primary and secondary clutches. What does this springs represent? Is there any use of them? How to choose the needed one? Is that a good idea at least ?:grin

I am looking for confirmation on the Primary one way clutch bearings for the 2002 can-am quest 650. The shop manual lists these OEM parts based on the diagram on page 03-11-1 Primary Clutch on the Right side OEM BALL BEARING 711632370 I don't think you need to replace these on the secondary...

Installed some blackwater evos 28x10x12, loving the new tires :th_smiliewoo:, and was interested in getting a little bit more power down to them, especially in some pretty mucky areas up here in Alaska. Was looking into a clutch kit, but there is not a lot of info on them for the outlander 1000...