Can-Am ATV Forum banner

outlander 1000

  1. DIY Rad relocate XT1000 for under $60

    Can-Am Outlander
    I really wanted a factory rad relocate but for $560 Canadian, i wasn't ready to fork out the wallet especially when i could build something similar. It started out with scrap trampoline pipe which is the same thickness as the OEM bumper, then with $20 in mesh and flat bar i made the front and...
  2. Can am xmr outlander reverse issues

    Can-Am XMR
    2014 outlander xmr 1000 putting it in reverse and hitting the throttle the bike revs up and it sounds like the intake is blowing or sucking air along with sputtering causing it not to shift out of reverse after hitting the throttle while forcing the shifter to high/ low it will finally go in to...
  3. Outlander 1000 LTD with Tracks width

    Can-Am Outlander
    Hi everyone I'm about to buy the Apache Backcountry tracks for my Outlander 1000 Max LTD, but I'm not sure if it will fit on my trailer. Does anybody know the total width of the vehicle with the tracks on? Thanks!
  4. 2012 Can am outlander 1000 bogging

    Can-Am Outlander
    Hi, i have a 2012 can am outlander 1000, ive tried everything, changed my spark plugs, clutches, emptied my fuel, brand new fuel filter and put a fresh tank of gas in it. The bike bogs out when i first punch it (it wont wheelie) just bogs down, and my max speed is 70km/h then it starts to bog...
  5. 04 outlander 400 cv axle

    Can-Am Outlander
    i have a 2004 can am outlander 400 high output and it needs a front right axle and i have a parts bike which is a 2006 outlander 400 xt will it work???
  6. Outlander 1000 - when to replace timing chain and guides?

    Can-Am Outlander
    Hi all, I picked up a 2014 Outlander 1000 XT with high mileage (15,000km & 950 hrs). I pulled the covers to adjust the valves and inspect the timing chain + guides. I have looked at a few manuals and scoured the internet but have found absolutely nothing on wear indicators. There also has not...
  7. XMR 1000 6” Lift Options

    Can-Am XMR
    In final preps to purchase my lift 6”. No Portals. I’d really loto hear your thoughts on my options. I’m not a speed demon, and ride mostly mud. Have been to WV a couple times for a group ride in the mountains. Planning on a 32-34 tire on 14s. I ABSOLUTELY WANT SOMETHING DEPENDABLE!!! Super...
  8. Long time rider, new time Can-Am'er

    Please Introduce Yourself
    I s'pose this is where I'll say howdy doody to everyone and thank whoever runs this forum for allowing full access right from the first day of registration. There are many other online gatherings that restrict new users' access to everything the forum has to have (some sites are as much as 100...
  9. Clutch issues, Help

    Can-Am Outlander
    I have what sounds to be a very serious issue going on with my 2016 outty xmr1000. I will attach a video of said issue. Have had this banging noise when accelerating, and in reverse. I have changed everything from entire suspension to replacing the whole front diff, has been a nightmare cost...
  10. Selling my 6" Catvos lift

    Can-Am XMR
    Have for sale a 6 inch Catvos lift that I was running for the last year. Due to having kids it is now time to go back to stock suspension so the wife can enjoy riding my outty xmr 1000r. Lift sells for just under 4 thousand dollars, will take 2 thousand for it, and will also throw in the extra...
  11. Noise coming from front diff

    Can-Am XMR
    Was riding my 2016 Outlander xmr1000 this past Sunday, while accelerating from 0, and when in reverse, my outty is making a bang sound that seems to be coming from my front differential or driveshaft. Got under it and found 2 bolts that hold the diff in place were super loose, tightened them...
  12. Replacement headlight with LED's

    Can-Am Outlander
    Hi everyone I want to replace my stock headlights with LED's. I have ordered some off of Amazon and they came but they have a fan in the back of the headlight that will for sure get gummed up with mud. I'm wondering what everyone uses for replacement bulbs for high and low beams. I have a 1000...
  13. Outlander 1000 winch switch issue??

    Can-Am Outlander
    I've started plowing with my 2017 Outlander Max XT 1000 and have noticed the switch for the winch works fine for about 45 minutes or so then stops working for a while, then starts working again. Anyone come across this? Any suggestions on how to stop this from happening?
  14. Original Tiger Tail vs KFI Tiger Tail

    Can-Am / BRP
    Hello all, fairly new to the forum here. Hoping to get some good feedback. I'm looking at purchasing a Tiger Tail for my '13 Outlander 1000 XMR but I was wondering which brand to purchase? I know Team Tech Engineering is the original manufacturer of the Tiger Tail but the KFI Tiger Tail is a...
  15. 2017 Outlander XMR 1000 lift

    Can-Am XMR
    Hello all I ordered the super atv 6 inch lift for my xmr but was told that the brake lines are different. I am sure that I will get it figured out once it arrives. But was wondering if anyone has already gone through this process. Any help would be appreciated and if no one has then I will try...
  16. 6x6 Clutch kit?

    Can-Am Outlander 6x6
    Installed some blackwater evos 28x10x12, loving the new tires :th_smiliewoo:, and was interested in getting a little bit more power down to them, especially in some pretty mucky areas up here in Alaska. Was looking into a clutch kit, but there is not a lot of info on them for the outlander 1000...
  17. 2014 Outlander 1000-grease fitting Tips and Tricks

    Can-Am Outlander
    I know that there are 16 points that need to be greased, i am looking for any tricks you guys have to make it easier. I have hear anywhere from an hour to 15 mins to do them all. Also if you guys use a certain brand that you like. Thank You!
  18. Outlander Tire Issues

    Can-Am Outlander
    I want to put some mud tires on my 2014 outlander 1000 and I'm settled on the Terminators. The problem is 29.5" don't fit and I know I could do spring spacers or a bracket lift, but I don't want to ruin my ride quality with spacers and I don't want to wreck my axles with a bracket lift. So does...
  19. How Deep?

    Can-Am Outlander
    Does anybody know how deep I could go on my 2014 outlander 1000 xt before hitting my cvt intake?
  20. New guy haha

    Please Introduce Yourself
    Hi everyone i just joined the forum i bought my first can-am a couple weeks ago 2014 Outy XMR 1000 Camo..ive been around four wheelers my entire life but this is my first can-am so i have a lot to learn and still getting use to the power haha i still have my 2012 honda foreman on 28" backs and...
Top